Ghost 2 Immobiliser Reviews
The ghost 2 immobiliser is an innovative anti-theft system that uses advanced technology to stop car theft. This discreet device is unnoticeable by thieves, and it only starts the engine when a pin or app is entered.
It's weatherproof and connects to the CAN data network of your vehicle. It has a service/valet function that allows you to temporarily start your car when it is in the garage.
Easy to install
The Ghost immobiliser shields your car from theft of keys, cloning and hacking. It is a unique PIN code system that is incorporated into your car's ECU which makes it extremely difficult for thieves to spot or tamper with. Unlike traditional immobilisers, it does not require any special keys or sensors, and is completely hidden with no LEDs or signals to signal its presence. It's also cheaper than replacing an ECU or installing a new key fob and can lower the cost of your monthly insurance.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's instructions carefully. This will ensure that the device operates properly and efficiently. Once the installation is complete check the system by entering the PIN code, then turning on the engine. Regular testing will enable you to identify any problems early on.
Make sure you check the position of CAN H and L wires before beginning the installation. They are vital to powering the immobiliser, and it is essential that they are properly connected. Labelling the wires will help you locate them during installation. Once you have identified the wires, connect them to a 12V power supply and the grounding source. Be sure to utilize a fuse tap when required to shield the connections from short circuits or damage.
After connecting the wires, neaten up the wiring with cable ties to prevent potential interference. You can also cover the connections with insulation tape or heat-shrink tubing. This will shield the device from electrical shorts, and extend its lifespan. It is a good idea to test your Ghost 2 immobiliser once the wiring is secure.
In the event that you have to hand over your vehicle, for instance for servicing or valet parking for valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. Press the brake pedal and hold the accelerator for a number of times equal to the first digit in the emergency code. The system will enter service mode. This is confirmed by flashing five times the indicator signal.
It is simple to change PIN codes
It is simple to safeguard your vehicle from theft using a ghost 2 immobiliser. It is discreetly installed inside the vehicle and can be accessed by a unique code. The device communicates with the vehicle ECU through its data bus and does not rely on radio frequency signals, as alarm systems that are sold on the market or traditional Thatcham immobilisers do. This makes it harder for thieves to hear the click of an immobiliser relay or add new keys. The control unit is concealed within the wiring of the vehicle's dashboard, and can't be physically altered to reset the system.
The ghost 2 immobiliser connects to the vehicle's CAN Data network. It uses buttons on the door panels, the steering wheel and the center console, to create a customisable series of up to twenty button presses, which must be entered to start the engine - similar as a PIN. This next-generation system doesn't require any wire cutting upon installation and can be fully reprogrammed at anytime. You can even start your car in Service or Valet mode after you hand it to a mechanic do work.
You can also make use of the app to alter your PIN code, or deactivate it completely if you have lost your keys. This feature is particularly useful when you've given your car away to someone else for parking or valet services. It will stop them from starting the car and then driving it off without your permission. It is also undetectable by professional thieves, as it doesn't utilize circuit cuts or radio frequencies.
The ability of the immobiliser to prevent relay thefts is another great feature. Relay theft is a popular method of car theft, where criminals attack the diagnostic port on your car, then modify the original signal that is sent by the key to the vehicle's ECU to trick it into believing that a valid key is present. The immobiliser of the traditional model can be manipulated in this manner, however with the ghost 2 immobiliser the signal is blocked by the immobiliser before it reaches the ECU.
Easy to use app
Ghost 2 is a revolutionary immobiliser that protects your car from key-cloning, hacking, and key theft. It connects to the CAN data network of your vehicle and requires the use of a PIN number to start the engine. It also stops thieves from using signal spoofing or device spoofing that are popular methods of stealing vehicles.
The system is easy to use and operates similar to a standard car alarm. Once you have installed it, you are able to create a unique PIN sequence that is up to 20 digits in length, which will have to be entered prior to the vehicle's start. This will prevent the vehicle from being taken even if the keys are stolen. If you wish to disable the system, you can do so by using an app on your smartphone.
The ghost is completely silent, and it does not emit radio frequency signals. It is a discrete weatherproof device that can be placed anywhere inside your car. It can be hidden under the dashboard, door panels or the steering wheel. It communicates with your ECU via the CAN data circuit and is not affected by diagnostic tools that thieves use to identify security systems. It is not affected by jamming devices which spoof codes.
It is a concealed installation that doesn't require any cutting of wires or modifications to the vehicle and can be utilized as an anti-theft system for any vehicle. Its technology has been proven be efficient and is in line with TASSA standards. The Ghost is a fantastic choice for classic or sports automobiles. It can also be used as a way to protect vehicles being rented on apps like Turo.
The Autowatch Ghost 2 represents the next generation of auto immobilisers. The system is inaccessible to thieves and prevents the vehicle from starting until they have your PIN or have been authorized by the app. It also doesn't emit radio frequencies or other signals that could be detected by scanners. Installation is simple and quick. The app is simple to navigate and offers a user-friendly interface which makes it simple to install and use. It also comes with an GPS tracker to assist police locate and find the vehicle.
Simple to reset
It is possible to protect your vehicle from theft by using an immobiliser ghost 2. It is integrated into your vehicle's ECU creating a wall that thieves cannot break through without the proper pin. It's also TASSA certified which means it's recognized by insurance companies. It's a great tool to stop car theft, and will save you a lot of dollars in the long run.
The Ghost system unlike traditional alarms or immobilisers, which require cutting of circuits it is directly connected to your vehicle's CAN data network. It operates by pressing the buttons on your dashboard as well as the steering wheel. You can create a unique PIN sequence that is up to 20 presses in length. The PIN must be entered before the engine can begin like the credit card PIN. Ghost is unnoticeable to thieves, and there are no LED indicators to give away its presence, which makes it the most reliable aftermarket CAN bus immobiliser on the market today.
The Ghost system has another advantage that it does not transmit radio frequency signals. This means that it is not stolen or scanned by thieves. This prevents key attacks that replicate and relay attacks as well as the common method of hacking into the computer system of a car using its CAN bus by searching for signals. Additionally to that, the Ghost system is designed to be completely hidden in your vehicle and there are no LEDs or other signals that signalize its presence.
The system also features an option for a Transport Mode that disables the Ghost system which is useful in situations when you need to temporarily deactivate it, such as during transportation or servicing. This mode isn't as effective as Service Mode as it doesn't disable the Ghost system when you exceed 31 mph in 15 minutes.
To reset your ghost 2 immobiliser you'll need the emergency code, which you can obtain from your installer. ghost immobiliser tracker is usually hidden under a scratch-off area on the card included when you installed the device. This emergency code should be secured and stored in a secure place like your wallet at home.